2016 EBY MAVERICK LS BH1MLS 6’6″ W X 16′ L X 6’6″ H. BUMPER PULL STOCK TRAILER. 2 5200 LB TORSION BRAKE AXLES, 235/80/R 16 RADIAL TIRES ON 8 LUG 16″ WHEELS, SPARE TIRE, CENTER GATE, STOCK # 2026762
Available Floor Lengths: 13Õ & 16Õ
Outside Width: 6Õ5Ó
Inside Height: 6Õ6Ó
- 13′ Model
- GVWR: 8,130lbs.
- Axles: (2) 3,500# rubber ride (greased packed bearings), 96Ó wide
- Wheels: 16Ó x 6Ó heavy duty steel, 6-lug
- Tires: (4) LT215/85R16 steel belted radials, load range E
- Brakes: 10Ó x 2-1/4Ó electric on both axles
- 16′ Model
- GVWR: 10,000lbs.
- Axles: (2) 5,200# rubber ride (greased packed bearings), 96Ó wide
- Wheels: 16Ó x 6Ó heavy duty steel, 8-lug
- Tires: (4) ST235/85R16 steel belted radials, load range E
- Brakes: 12Ó x 2Ó electric on both axles Ð 16Õ.
- Safety Equip.: Two chains and electronic breakaway kit.
- Landing Gear: Single speed top-wind crank.
- Coupler: 2-5/16Ó ball coupler (12,500# rating).
- Front Nose: Tapered V-nose with .080 aluminum smooth sheets and vertical hat posts. (3) Cast
- Assembly: aluminum corner caps and extruded radius front corner posts.
- Slats: Standard exterior slat spacing. Pattern A on all 6Õ6Ó trailers and pattern B on all 7Õ inside height trailers. 8Ó openings are notched for optional closures.
- Posts: Extruded aluminum, 1Ó x 3Ó tapered tubular side posts, spaced on 18Ó centers maximum.
- Bottom Rails: 12Ó extruded aluminum.
- Top Rails: 6Ó extruded aluminum.
- Crossmembers: 3Ó extruded aluminum J-beams on 12Ó centers.
- Floor: .125 flat aluminum diamond plate.
- Side Door: 29Ó wide, curb side, 10-3/4Ó from drop sheet.
- Rear Frame Assembly: 3Ó x 5Ó tubular extruded aluminum with Eby cast aluminum corner caps.
- Rear Door: Full swing with (2) 4Ó extruded aluminum offset hinges for extended swing radius. Hinges are mechanically fastened and welded to rear frame. 30Ó wide exterior sliding door on roadside with polyurethane rollers at the top and UHMW wear pads at the threshold.
- Sheet: One-piece .040 aluminum externally riveted to top rail on 4Ó centers.
- Bows: Arched, hat shaped 1-1/2Ó x 4Ó extruded aluminum on 24Ó centers.
- Std. Partition: (Partition is optional on 13Õ model) Extruded aluminum tube and punched sheet construction with outside release slam latch. Extruded aluminum pipe hinge with nylon bushing mounted curbside. Partition located on post nearest centerline of box.
Lights & Wiring (Meets all US and Canadian Regulations.)
- Lights: 12-volt D.O.T. approved, LED.
- Wiring: A.T.A. color coded, wiring harness.
- Rear Lights: Modular, turn-tail-stop, LED. One light each side (red).
- Inside Lights: One sealed beam, with external rear water resistant switch.
- Tire Carrier: None standard Ð Added only with spare wheel and tire option, mounted on exterior front sheet.
- Fenders: Extruded rolled aluminum.
- Bumpers: Full width 3Ó molded rubber.
- Skid Plates: (2) 3/16Ó formed aluminum.
- Paint: Steel parts painted silver.
- Conspicuity Tape: Meets all US and Canadian regulations.